Part #2 https://www.youtube.com/watch?v=IrWBQBgoqf0
Alexa Taking out the trash
https://www.youtube.com/edit?o=U&video_id=sFJE_PsUlm8
5V-36V 350W DC Brushless Motor Controller BLDC PWM Driver Board
https://goo.gl/qnQ32U
Specification :
Operating voltage: DC 12V-36V
Operating Current: less than or=15A
Driver Power: less than or =500W
Speed Voltage: 0.1V-5V
Operating Temperature:-40-85C
Humidity: 90%RH
Stall protection:Yes
Enable Control: Yes
Over-current protection: Yes
Steering control: Yes
Speed control signal: Yes
Size: 63*42*17mm(L*W*H); Probe size 3mm,length: fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out:
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side:
GND control terminal ground
VR the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF reversing control(connected to 5V or ground can charge the motor rotation direction)
M tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V 5V control terminal
HALL for the hall terminals:
5V, Hall power positive
Ha, Hall signal
Hb, Hall signal
Hc, Hall Signal
GND, Hall negative
Wiring:
Control terminal for SET:
1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster
2. Motor steering control wiring methods: you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V
3. Pulse speed signal: high and low output . IC can not understand the information with the customer request
Hall signal inputs for hall:
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall
Note: Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the sequence, need to be adjusted, please parents who pay attention! If the line sequence wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!!
Motor driver board 12-36V DC power input,
VCC positive power supply,
GND power supply is ground (0 Volt).
Electrical wiring methods:
Brushless DC motor for the three lines, corresponding MA/U,MB/V,MC/W
Tips: If you use less than 60W, without additional heat sink , be sure to add more than 60W heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
, https://i.ytimg.com/vi/TaCukBg4Hj8/hqdefault.jpg
source
Can I use the 36v hoverboard battery for two boards tough?
code ?????
I'm having very low torque at low speed, cannot find out why? Any thoughts? Thanks!
can you share the 2 motor controller specs and Datasheet
Hi I want to make an electric quad using 4 hoverboard motors , if I want to control all of them from a single pod, I need to buy more board and connect them to a single pod and use 4 batteries with them? Or I can use one board with 4 motors and a single battery?
Thanks in advance!
Yes great job
dear l just bought bldc motor controller exactly same as you have but unfortunately it does not give output power. input is 20V battery. no output voltage. do you have any comments? thanks
Hi..how about torque? same like nema 42? whats Nm torque??
Vesc would be a option to ? realy sad the ceap ones dont have break :/
Hi! Do you mind sharing your code and development platform? thanks
i swear this guys accent is indian mixed with american
thank you indian man you really did me a favour
Hello, I'm Orlando Tristão, I'm from Portugal and I'm in a wheelchair. Congratulations on this video, no doubt many will benefit from your project. Please help me if you feel well. I need to adapt two Hoverboard motors, (36V 500W), to my wheelchair. I need to know which controller is ideal and how I can connect a joystick. Could you please help me? I await your dear reply. a hug, thank you very much
Wonderful video, gonna go watch Part 2 now…
Question: My hoverboard motors had one more wire coming out of it – a white one… Is that anything you've seen before? It might be power for the LEDs in the hub – I will check that out too…
Ciao bel video, volevo chiedere se è possibile collegare un acceleratore (throttle) a 5 fili al posto del potenziometro. Grazie in attesa di un vostro riscontro vi porgo i miei cordiali saluti
This can brake and reverse?
Ey! when you turn on the system, does the wheel have the brake activated?
Sub Indonesia
Hi, I tried using the same BLDC controller with the same wiring. When I input 27v battery (2A), things heat up a little bit within 1 minute, and one capacitor exploded. the controller should be able to handle max 36v. You mentioned the controller fired when you use original battery from the hover board. If I use lower voltage, the wheel won't spin. Do you know any controller can handle 27v input power? The capacitor that exploded rated 16v, next to the Set wiring.
thank you for the information, i learn something
how much the controller for 3 hover motor
Great Video, where did you get the female wire adapter that the battery plugs into?